Tools You Need to Set Up a New Tub

Schedule Now

We have unearthed this great article involving How to Install a Bathtub Yourself listed below on the internet and think it made sense to share it with you on my blog.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bath tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard task. If the old tub is easily available, the job can relocate rapidly; if you have to open up a wall to eliminate the old tub as well as place the new tub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will need an assistant to vacate the old bathtub as well as embeded in the new one. Make certain you have qualified on your own for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed job, it is better to think about using one before you start. Chances are you might require a professional plumber to make tube links.
This article will aid you mount a new tub in your bathroom if you have currently acquired a brand-new tub as well as do not require to transform the setup of your previous supply of water pipes.
Your devices and product list ought to make up the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be rather troublesome because of the limited access that is typically the situation.
    Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
    Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipelines.
    If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
    Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be linked to the tap ends first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Mounting the Tub


    Utilizing both wood boards under its feet, put the tub in the required position. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little points.
    The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the bathtub until the level checks out level.
    To mount taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
    Switch on the water supply and also check all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bathtub as well as additionally examine the overflow electrical outlet and also the typical electrical outlet for leaks.
    Finally, take care of the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bath tub has actually been utilized a minimum of once as this will certainly settle it into its last placement.

    Getting ready for the Installation


    First of all, the supporting framework supplied with the bath should be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to prevent stress on the bath tub.
    Fit the versatile faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you make use of every one of the supplied washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.

    Tiling Around the Bathtub


    In the area where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, creating the water to permeate the wall between the bathroom as well as the tiling, causing problems with dampness and feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the motion experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this activity prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant sticky as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    As a fervent reader about Tools You Need to Install a New Bathtub , I figured sharing that chunk was really useful. Do you know about somebody who is occupied with the topic? Be sure promote it. Thanks so much for taking the time to read it.




    About This


    Leave a Reply

    Your email address will not be published. Required fields are marked *